Teradek Bolt 1000 Tx/Rx Set

  • $5990.00
Qty:  
Previous image
Teradek Bolt 1000 Tx/Rx Set
Next image
Zoom image
  • Weight
    15 lbs
  • SKU
    10-0965

Bolt is a premium wireless video solution for cinematographers, broadcasters, and independent content creators. 

Transmit uncompressed 1080p video wirelessly over 3000 feet line-of-sight with the Teradek Bolt Pro 1000 Wireless Video Transmitter/Receiver Set. Included in this set are a Teradek Bolt Pro 1000 transmitter and receiver, both equipped with 3G-SDI and HDMI ports. The transmitter can pair with and multi-cast to up to four receivers. When transmitting uncompressed video, latencies of less than one millisecond can be achieved if no other video processing is necessary.

Transmitting across the 5 GHz frequency range, the pair utilizes Dynamic Frequency Selection (DFS) to find a clean signal between the transmitter and receiver. This is desirable when working in areas with crowded frequencies. Both transmitter and receiver are equipped with HDMI and SDI ports, which allow for cross conversion from HDMI to SDI and SDI to HDMI during transmission. The transmitter also features a loop-through SDI output. The USB GRAB engine streams the uncompressed video straight out of the receiver and into a PC for immediate recording. The included waterproof case with custom-cut foam carries the components during transport and storage.

What's In The Box?
2 x SDI BNC to BNC 10 in. Cable
2 x HDMI Type A to Type A 18 in. Cable
1 x Protective SKB Case - military-standard waterproof hard case with custom foam (13.5in x 9.5in x 6.5in - 34.29cm x 24.13cm x 16.51cm)
1 x 1-Year Warranty

Transmitter
2 x Wireless Antennas (5dBi 5.8GHz)
1 x 2-pin Connector to PowerTap 18 inch Cable
1 x Hot Shoe Adapter (1/4"-20 inch)
1-Year Warranty

Receiver
1 x Lightstand Adapter (1/4"-20 inch)
1 x Thumb Screw Plastic Head 1/4-20 thread, 1.25 length
1 x PSU 2-pin Connector to 18W AC Adapter 6ft cable
5 x Wireless Antennas (2dBi 2.4/5.8GHz) - For Rx
1 x USB 3.0 Cable A to Micro B (3ft Length)
1-Year Warranty

See the product video introduction:

See a setup video tutorial:

 

 


    Transmitter

  • Details
    Video Input
    1 x 3G/HD/SD-SDI, BNC (75 Ohms)
    1 x HDMI

    Video Output
    1 x 3G/HD/SD-SDI, BNC (75 Ohms)
    1 x HDMI
    1 x Micro-USB 3.0

    Delay
    <0.001 sec (when no video format conversion is enabled)

    Color Sampling
    RGB 4:4:4 (HDMI out, 8-bit color)
    YCbCr: 4:2:2, 8-bit for SDI (10-bit with no format conversion and FPGA v1.1.0 or later)

    Formats
    1920 x 1080p 60/59.94/50/30/29.97/25/24/23.98
    1920 x 1080PsF 30/29.97/25/24/23.98
    1920 x 1080i 60/59.94/50
    1280 x 720p 60/59.94/50
    576 50 (via HDMI ports only)
    480p 59.94 (via HDMI ports only)
    576i/480i
    NTSC/PAL

    Wireless Range:
    Up to 3000' / 914 m line-of-sight

    Non-DFS Frequencies:
    5.19 to 5.23 GHz and 5.755 to 5.795 GHz (US) / 5.19 to 5.23 GHz (EU & JP)

    DFS Frequencies:
    5.27 to 5.55 GHz and 5.67 GHz (US) / 5.27 to 5.67 GHz (EU & JP)

    RF Power
    22 dBm EIRP (with one 5 dBi TX antenna)

    Noise Rejection
    Can coexist with Wi-Fi and 5 GHz cordless phones

    Audio
    48 kHz 24-bit PCM

    Power
    Volts: 7 to 28 VDC

    Consumption:
    8.5 W

    Connector:
    2-pin LEMO

    Dimensions
    5.5 x 3.5 x 0.9" / 13.9 x 8.9 x 2.5 cm

    Weight
    13.3 oz / 376 g


  • Receiver

  • Details
    Video Output
    1 x 3G/HD/SD-SDI, BNC (75 Ohms)
    1 x HDMI
    1 x Micro-USB 3.0

    Delay
    <0.001 sec (when no video format conversion is enabled)

    Color Sampling
    RGB 4:4:4 (HDMI out, 8-bit color)
    YCbCr: 4:2:2, 8-bit for SDI (10-bit with no format conversion and FPGA v1.1.0 or later)

    Formats
    1920 x 1080p 60/59.94/50/30/29.97/25/24/23.98
    1920 x 1080PsF 30/29.97/25/24/23.98
    1920 x 1080i 60/59.94/50
    1280 x 720p 60/59.94/50
    576 50 (via HDMI ports only)
    480p 59.94 (via HDMI ports only)
    576i/480i
    NTSC/PAL

    Wireless Range:
    Up to 3000' / 914 m line-of-sight

    Non-DFS Frequencies:
    5.19 to 5.23 GHz and 5.755 to 5.795 GHz (US) / 5.19 to 5.23 GHz (EU & JP)

    DFS Frequencies:
    5.27 to 5.55 GHz and 5.67 GHz (US) / 5.27 to 5.67 GHz (EU & JP)

    RF Power
    22 dBm EIRP (with one 5 dBi TX antenna)

    Noise Rejection
    Can coexist with Wi-Fi and 5 GHz cordless phones

    Audio
    48 kHz 24-bit PCM

    Power
    Volts: 7 to 28 VDC

    Consumption:
    8.5 W

    Connector:
    2-pin LEMO

    Dimensions
    5.5 x 3.5 x 0.9" / 13.9 x 8.9 x 2.5 cm

    Weight 13.3 oz / 376 g
  • Select Battery Adaptor
    V-Mount, Gold Mount
  • Brands
    • Brands
      Teradek

Wireless Video Refined
Bolt transmits visually lossless 4:2:2 video over the unlicensed 5GHz band at less than 1 millisecond of delay. Bolt’s new firmware ensures your system reaches its full potential right out of the box. We’ve also improved reconnect times so your wireless link is restored instantly when you come back into range.

Reliable Transmission in Any Environment
Operate more than twice as many wireless systems at one location or evade heavy interference. With Bolt 3000, you can transmit over 20MHz channels for a more robust signal in challenging RF conditions.

*20MHz channels allow you to operate more wireless systems at once in a single location and offer a more robust wireless link in challenging RF conditions. However, audio transmission, as well as interlaced, PSF, and 1080p60/50 frame rates are not currently supported.

Smaller, Lighter, and Even More Rugged
The Bolt 1000 and 3000 transmitters are 20% smaller than previous systems and lighter too. We’ve also improved their resilience in high heat conditions so that they operate flawlessly all the way up to 130F.

Sidekick II: Universal Bolt Receiver
Compatible with Bolt 500, 1000, and 3000, the 300ft Sidekick II is the perfect solution for a director’s monitor kit. With an SDI output, support for timecode and start/stop flags, and a built-in test pattern generator, this universal receiver is the most affordable way to monitor a Bolt feed on set.

More Channels to Transmit Over
Bolt also offers manual frequency control so your crew can carefully manage your wireless workflow wherever you’re shooting. The Bolt 3000 can operate on 2 new DFS channels, allowing interference-free video transmission in more environments than ever before.

Transmit to Multiple Receivers
All Bolt models are multicast capable up to 4 receivers of the same range at the same time. This means you can send your video feed to monitors, switchers, recorders, and even Teradek Cubes simultaneously with no loss in quality or added delay.

Built-in Cross Conversion
Every Bolt model supports real-time standards and cross conversion from TX to RX, allowing you to automatically convert resolution, frame rate, and inputs.outputs (HDMI / 3G-SDI) without any additional hardware.

Metadata & Time Code Support
All 3G-SDI Bolt models support metadata, timecode, and start/stop flags from many camera manufacturers, including RED, ARRI, Canon, Sony, and Panasonic.

3D LUT Integration
Apply the look you’re after directly to your wireless video feed using Bolt’s integrated 3D LUT technology. Upload your own LUTs using the free Bolt Manager software or select from a number of built-in presets using Bolt’s OSD.

Cut Through the Interference
The Panel Array Antenna is your go-to solution for cutting through wireless interference in crowded environments. When attached to a Bolt 1000 or 3000, the antenna provides an extremely robust directional signal that will ensure your signal arrives uninterrupted.

Built-In HDMI to SDI Converter
Perfect for use with MoVI and other gimbals, Bolt’s TX features a built-in HDMI to SDI converter, allowing you to connect both your on-camera monitor and video source via the same device.

Forget About Capture Cards
Bolt’s USB 3.0 GRAB Engine allows you to ingest a Bolt feed directly into a computer or your DIT cart without any added delay or loss of quality.

The Bolt Identity
To better identify which systems are paired on set, a removable top plate on Bolt’s TX and RX can be swapped out for a colorful anodized one.

Built Like a Tank
Bolt is housed in a hardened aluminum chassis designed to withstand years of abuse in both extremely hot and cold conditions. Both the TX and RX feature 1⁄4”-20 holes for mounting to cameras and monitors as well as 2-pin Lemo connectors for power. Unique to Bolt 1000 and 3000, a built-in OLED on the RX allows you to quickly configure the system as well as apply 3D LUTs at the touch of a button.